Go Company

 

 

This post which follows relating to How to Install a Bathtub Yourself is absolutely enlightening. You should investigate for yourself.

Setting up a tub isn't exactly brain surgery, yet it does need solid plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately difficult task. If the old bathtub is readily accessible, the task can move quickly; if you need to open up a wall to remove the old bathtub as well as position the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require a helper to vacate the old bathtub and embeded in the new one. Make sure you have actually qualified on your own for the task and fit attempting it. Rather than working with a professional to take control of a halfway-completed job, it is better to take into consideration using one prior to you begin. Chances are you might need a professional plumber to make tube links.
This short article will aid you set up a new tub in your shower room if you have currently purchased a new bathtub as well as do not require to change the setup of your previous supply of water pipes.
Your devices and product checklist need to make up the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin ensuring that the washers remain in place between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap connectors. The former type ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Setting up the Tub

Utilizing the two wooden boards under its feet, put the tub in the required setting. The wooden boards are useful in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be attained by examining the level and adjusting the feet on the bath tub till the level checks out level.
To set up taps, fit the bottom of the outermost adaptable faucet port to the suitable supply pipe by making a compression sign up with; then do the very same for the various other tap.
Activate the supply of water and inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill the bath tub and additionally inspect the overflow outlet and also the typical outlet for leakages.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and sealing around the bath tub ought to wait until the bathtub has actually been utilized at least when as this will resolve it into its last setting.

 

 

Preparing for the Installment

Firstly, the sustaining framework provided with the bathroom must be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to stop stress on the bath tub.
Fit the flexible faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final placement.

 

 

Tiling Around the Tub

In the location where the bathroom meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about complications with dampness as well as feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to permit the activity experienced when the bathtub remains in usage. The sealer can break relatively early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently offered on the market. It is recommended to fit the tiles using waterproof or water-proof sticky as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I am just very intrigued by Tools You Need to Install a New Bathtub and I'm hoping you enjoyed our page. Sharing is caring. Who knows, you might be helping someone out. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .

Schedule Today